Product News

• What Is The Difference between Roots Blower And Screw Blower?

  Roots blowers and screw blowers have their own characteristics, and the choice should be based on the needs and scenario conditions of the specific application. Roots blowers are suitable for occasions with large flow and low pressure requirements, while screw blowers are more suitable for applications that require high pressure and stable airflow.

  Products Release October 17, 2024
• Regarding The Production of Calcium Carbonate Filler Masterbatch, These Five Points May Be Worth Looking at

  Calcium carbonate filler masterbatch is a particle with a volume similar to the base resin of plastic products made by mixing calcium carbonate with carrier resin and mixing and granulating. It has a wide range of application value in the plastics industry. Before masterbatch processing, the surface of calcium carbonate powder is modified to increase its dispersibility, which can greatly improve the crosslinking with the resin. However, there are still 5 issues that need to be paid attention to during the production of calcium carbonate filler masterbatch.

  Material Introduction October 14, 2024
• A Complete List of Plastic Raw Material Terms——No Longer Worried about Not Being Able To Understand The Physical Properties Table

  In the quality indicators of raw materials, we often encounter some terms. Accurately understanding their meanings will help us better grasp the performance of raw materials. Here are some commonly used terms.

  Material Introduction October 10, 2024
• List of PS Modified Formulas

  List of PS modified formulas 1. PS blending 2. Flame retardant reinforced toughened PS/PBT blended alloy material 3. PS flame retardant 4. Halogen-free flame retardant modified HIPS 5. PS foaming 6. Low foaming HIPS plastic paper

  Material Introduction October 07, 2024
• What Difficulties Are Faced in The Manufacturing of Glass Fiber Reinforced Nylon? Attached Are PA66 Applications with Different Fiber Adding Ratios

  The reinforcing materials used in reinforced nylon are mainly fibrous substances such as glass fiber, carbon fiber, and whiskers, among which glass fiber reinforcement is the most widely used. The rigid strength and hardness of the material can be significantly improved through glass fiber reinforcement, and the dimensional stability and heat resistance of the material can be significantly improved. Since nylon itself is not strong enough, 10-30% of fiber is added to increase its strength. In particular, 30% intensity is recognized as the most appropriate ratio.

  Material Introduction October 03, 2024
• Why Didn't The Sliding Additive Work?

  To improve the film's sliding properties, a sliding additive is introduced during its production (usually the active substances are oleamide and erucamide). After film extrusion, the additive migrates to the surface and creates a sliding layer on it, due to which the friction coefficient is significantly reduced and the film's sliding properties are improved.

  Material Introduction September 26, 2024
• Have You Solved These Problems Encountered in The Production Process of TPE Extrusion Materials?

  Have you solved these problems encountered in the production process of TPE extrusion materials? 1. Rough surface of molded product 2. Scaling 3. Unstable extrusion volume 4. Deformation 5. Stripes

  Products Release September 23, 2024
• Application of Loss-in-Weight Scale in Plastic Modification Operation

  The loss-in-weight scale uses the weighing hopper and the entire feeding mechanism as a scale body for weighing. As the material flows out of the loss-in-weight scale, the control system collects the weight signal of the scale body at a high speed and high frequency to obtain the weight reduction of the material in the weighing hopper per unit time. Then, through TRUSTAR's unique filtering and optimization processing, the actual flow rate of the loss-in-weight scale is obtained. At the same time, the control system compares this feeding speed with the preset given speed, and calculates the comparison result and feeds it back to the feeding mechanism of the loss-in-weight scale to automatically correct the feeding speed of the feeding mechanism, forming a closed-loop control, so that the actual flow rate is infinitely close to the given flow rate, thereby meeting the control requirements.

  Products Release September 19, 2024
• What Should We Pay Attention To in The Underwater Pelletizing Process of ABS?

  Regarding the production process of ABS resin, in industrial applications, the underwater strand pelletizing process is more common and more mature. However, the pelletizing system is not closed and there may be some uncertain factors that may lead to product contamination, such as the die plate of the industrial extruder, the water bath, etc.

  Products Release September 16, 2024
• Analysis of The Reasons for Poor Color Dispersion After Using Color Masterbatch

  Masterbatch is the most common plastic coloring method and is widely used in the plastic processing industry. Dispersion is one of the most important performance indicators of masterbatch. Obviously, dispersion has a vital impact on the quality of plastic products.

  Material Introduction September 12, 2024